|
Size: 4493
Comment:
|
Size: 9187
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 18: | Line 18: |
| Silicon is the construction material of choice - the solar cell is made of silicon, and the processors and memory are also. Here are some relevant properties of silicon, !SiO2 glass, gallium arsenide, copper, aluminum, tantalum, and indium tin oxide, which will make up 99% of the weight of a server-sat: | Silicon is the construction material of choice - the solar cell is made of silicon, and the processors and memory are also. Here are some relevant properties of silicon, !SiO2 glass, gallium arsenide, copper, aluminum, silver, gold, tantalum, indium tin oxide, kovar, invar, alumina, and pyrolytic graphite, which will make up 99.9% of the weight of a server-sat: |
| Line 20: | Line 20: |
| || property || Si || !SiO2 || !GaAs || Cu || Al || Ta || ITO || Kovar || || Density g/cm^3 || 2.33 || 2.65 || 5.32 || 8.96 || 2.7 || 16.7 || 6.43 || 7.85 || || Thermal Coefficient of Expansion 10-6/K || 2.6 || 0.5 || 5.7 || 16.5 || 23.1 || 6.3 || 10? || 5.3 || || Heat Capacity J/g-K || 0.71 || 0.74 || 0.33 || 0.38 || 0.90 || 0.14 || || || || Thermal Conductivity W/m-K || 149 || 1 || 55 || 401 || 237 || 58 || || || || Youngs Modulus GPa || 150 || 73 || 86 || 110 || 70 || 186 || 116 || || || Tensile Strength MPa || 7000 || 50 || 57 || 210 || 40 || 200 || 120 || 270 || || Atomic Weight (avg/atom) || 28 || 20 || 72.3 || 63.5 || 27 || 181 || 56.7 || 57.2 || || Resistivity nano-ohm-m || - || - || - || 17 || 27 || 131 || 2200 || || || Dielectric Constant || 11.8 || 3.9 || 12.9 || - || - || - || - || - || Data mostly from wikipedia and various places online. Tensile strength untrustworthy, and many parameters are anisotropic. Use only for rough estimates. |
|| property || Si || !SiO2 || !Si3N4 || !GaAs || Cu || Al || Ag || Au || Ta || ITO || Kovar|| Invar|| !Al2O3|| PyroC|| || Density g/cm^3 || 2.33 || 2.65 || 3.20 || 5.32 || 8.96 || 2.7 || 10.5 || 19.3 || 16.7 || 6.43|| 7.85 || 8.05 || 3.96 || 2.25 || || Coeff. of Thermal Expansion 10-6/K || 2.6 || 0.5 || 3.2 || 5.7 || 16.5 || 23.1 || 18.9 || 14.2 || 6.3 || 10? || 5.3 || 1.3 || 5.5 || 4.3 || || Heat Capacity J/g-K || 0.71 || 0.74 || 0.71 || 0.33 || 0.38 || 0.90 || 0.24 || 0.13 || 0.14 || - || 0.44 || 0.51 || 0.75 || 0.72 || || ''Heat Capacity MJ/m^3^-K'' || 1.65 || 1.96 || 2.27 || 1.76 || 3.40 || 2.43 || 2.47 || 2.49 || 2.34 || - || 3.45 || 4.11 || 2.97 || 1.62 || || Thermal Conductivity W/m-K || 149 || 1 || 30 || 55 || 401 || 237 || 430 || 320 || 58 || - || 17.3 || 10.1 || 46 || 1950 || || ''Specific thermal conductivity'' || 64 || 0.4 || 9.4 || 10 || 45 || 88 || 41 || 16 || 3.5 || - || 2.5 || 12 || 11.6 || 870 || || ''Thermal Diffusivity mm^2^/s'' || 90 || 0.5 || 13 || 31 || 118 || 98 || 174 || 129 || 25 || - || 5 || 2.5 || 3.9 || 540 || || Youngs Modulus GPa || 150 || 73 || 260 || 86 || 110 || 70 || 83 || 78 || 186 || 116 || 140 || 148 || 370 || 4.8 || || ''speed of sound km/s'' || 8.0 || 5.2 || 9.0 || 4.0 || 3.5 || 5.1 || 2.8 || 2.0 || 3.3 || 4.2 || 4.2 || 4.3 || 9.7 || 1.5 || || Tensile Strength MPa || 7000 || 50 || 70 || 57 || 210 || 40 || 170 || 100 || 200 || 120 || 270 || 680 || 300 || - || || ''Atomic Weight (avg/atom)'' || 28 || 20 || 20 || 72 || 64 || 27 || 108 || 197 || 181 || 57 || 57 || 56 || 20 || 6 || || Resistivity nano-ohm-m || - || - || - || - || 17 || 27 || 16 || 22 || 131 || 2200|| 490 || 820 || - || 14000|| || Dielectric Constant || 11.8 || 3.9 || 7.5 || 12.9 || - || - || - || - || - || - || - || - || 9.9 || - || Data mostly from wikipedia and various places online. See also [[ http://www.matweb.com | Matweb]] the material properties website, [[http://www.ece.byu.edu/cleanroom/CTE_materials.phtml | B.Y.U. CTE table ]]. Tensile strength untrustworthy, and many parameters are anisotropic. Use only for rough estimates. The vast bulk of the material , and the largest pieces of of the server-sat, will be silicon. Since the server-sat undergoes wide temperature changes when it passes in and out of shadow, or undegoes thermal annealing, it will be more survivable if the non-silicon portions are made of composite materials that match silicon's 2.6E-6/Kelvin coefficient of thermal expansion (CTE). For example, Zicar Ceramics SALI-2 (search on Matweb]] is a mixture of 80% alumina, 20% silica with a a CTE of 6.2E-6 . Alumina, combined in different proportions with silica ( !SiO2 ) , might be nicely matched to silicon. Server sats will also need transparent materials and conductors that closely match silicon. The metals have very high CTEs, while !SiO2 has a very low CTE, so slotted metal wires with !SiO2 in the gaps is one way to make a "material" that is both conductive and has the same CTE as silicon. {{{#!wiki caution '''Volunteer Opportunities''' <<BR>>(1) Look for compounds and composite materials that closely match silicon. '''Stack compression during launch''' Booster systems vibrate during launch. If there are regions of higher and lower compressibility and mass density, there will be standing waves and resonances in a stack of server-sats. Ideally, the design would match the mechanical properties of all the materials used, but that is unlikely given other constraints. So the stacks may need to be resonance isolated from the boosters, reducing the payload fraction. A somewhat simpler constraint is to match the mechanical compression of the stack caused by acceleration forces. The materials (plus spacers if necessary) should have the same ratio of compressibility (modulus) to mass density, that is, the same speed of sound. That will minimize shear forces on the connections from the solar cells to the electronics and thruster ring. Mismatches will restrict the number of server-sats that can be stacked between spacers. Of course, all these problems must be designed out with mechanical CAD, and tested with centrifuges and shock tables on the ground. '''Curling''' can occur if the front and back sides of a server-sat (especially the solar cell) have different CTEs, and the server-sat undergoes repeated thermal cyclings. There is nothing inherent in a server-sat that establishes "flat" - it will flex until tensions and compressions are minimized. A slightly curved server-sat is not a severe operational problem. If the edges are turned up a few degrees, that will reduce collected solar energy very little. The main problem is the effect on the phasing of the radios. Significant curling will change the spacing of the radios at opposite sides of the curl, and lift them above the plane of the radios at the center of the curl. Without some means of determining precisely how much curl is there, the radios may be in incorrect phases. || {{attachment:curl_dwg.png }} || {{ attachment:curl_math.png }} || Here are some curls for various temperature and CTE changes and sizes: {{ attachment:curl_odg.png }} |
Manufacturing Server Sky
Devices and materials
A lot can be done on a very thin planar surface. Other things cannot be done easily. Here are some common electronic devices:
Thin Planar |
Non-planar |
Printed circuit laminates (ultrathin) |
Connectors |
Resistors |
cooling fins |
Planar Capacitors |
Wound foil capacitors |
pixel sensor arrays |
lenses |
liquid crystal light modulators |
LEDs (?) |
Striplines |
Coax |
Microwave-frequency inductors |
Low frequency inductors and transformers |
surface acoustic wave (SAW) resonators |
crystals |
beam lead interconnect |
wirebonds and solderbumps |
Silicon is the construction material of choice - the solar cell is made of silicon, and the processors and memory are also. Here are some relevant properties of silicon, SiO2 glass, gallium arsenide, copper, aluminum, silver, gold, tantalum, indium tin oxide, kovar, invar, alumina, and pyrolytic graphite, which will make up 99.9% of the weight of a server-sat:
property |
Si |
SiO2 |
Si3N4 |
GaAs |
Cu |
Al |
Ag |
Au |
Ta |
ITO |
Kovar |
Invar |
Al2O3 |
PyroC |
Density g/cm^3 |
2.33 |
2.65 |
3.20 |
5.32 |
8.96 |
2.7 |
10.5 |
19.3 |
16.7 |
6.43 |
7.85 |
8.05 |
3.96 |
2.25 |
Coeff. of Thermal Expansion 10-6/K |
2.6 |
0.5 |
3.2 |
5.7 |
16.5 |
23.1 |
18.9 |
14.2 |
6.3 |
10? |
5.3 |
1.3 |
5.5 |
4.3 |
Heat Capacity J/g-K |
0.71 |
0.74 |
0.71 |
0.33 |
0.38 |
0.90 |
0.24 |
0.13 |
0.14 |
- |
0.44 |
0.51 |
0.75 |
0.72 |
Heat Capacity MJ/m3-K |
1.65 |
1.96 |
2.27 |
1.76 |
3.40 |
2.43 |
2.47 |
2.49 |
2.34 |
- |
3.45 |
4.11 |
2.97 |
1.62 |
Thermal Conductivity W/m-K |
149 |
1 |
30 |
55 |
401 |
237 |
430 |
320 |
58 |
- |
17.3 |
10.1 |
46 |
1950 |
Specific thermal conductivity |
64 |
0.4 |
9.4 |
10 |
45 |
88 |
41 |
16 |
3.5 |
- |
2.5 |
12 |
11.6 |
870 |
Thermal Diffusivity mm2/s |
90 |
0.5 |
13 |
31 |
118 |
98 |
174 |
129 |
25 |
- |
5 |
2.5 |
3.9 |
540 |
Youngs Modulus GPa |
150 |
73 |
260 |
86 |
110 |
70 |
83 |
78 |
186 |
116 |
140 |
148 |
370 |
4.8 |
speed of sound km/s |
8.0 |
5.2 |
9.0 |
4.0 |
3.5 |
5.1 |
2.8 |
2.0 |
3.3 |
4.2 |
4.2 |
4.3 |
9.7 |
1.5 |
Tensile Strength MPa |
7000 |
50 |
70 |
57 |
210 |
40 |
170 |
100 |
200 |
120 |
270 |
680 |
300 |
- |
Atomic Weight (avg/atom) |
28 |
20 |
20 |
72 |
64 |
27 |
108 |
197 |
181 |
57 |
57 |
56 |
20 |
6 |
Resistivity nano-ohm-m |
- |
- |
- |
- |
17 |
27 |
16 |
22 |
131 |
2200 |
490 |
820 |
- |
14000 |
Dielectric Constant |
11.8 |
3.9 |
7.5 |
12.9 |
- |
- |
- |
- |
- |
- |
- |
- |
9.9 |
- |
Data mostly from wikipedia and various places online. See also Matweb the material properties website, B.Y.U. CTE table. Tensile strength untrustworthy, and many parameters are anisotropic. Use only for rough estimates.
The vast bulk of the material , and the largest pieces of of the server-sat, will be silicon. Since the server-sat undergoes wide temperature changes when it passes in and out of shadow, or undegoes thermal annealing, it will be more survivable if the non-silicon portions are made of composite materials that match silicon's 2.6E-6/Kelvin coefficient of thermal expansion (CTE). For example, Zicar Ceramics SALI-2 (search on Matweb]] is a mixture of 80% alumina, 20% silica with a a CTE of 6.2E-6 . Alumina, combined in different proportions with silica ( SiO2 ) , might be nicely matched to silicon.
Server sats will also need transparent materials and conductors that closely match silicon. The metals have very high CTEs, while SiO2 has a very low CTE, so slotted metal wires with SiO2 in the gaps is one way to make a "material" that is both conductive and has the same CTE as silicon.